ORing Industrial Networking . Industrial ethernet switch , Device Server , Serial , PoE , RS232 , RS-485 , RS422 , fiber , converter , IAP-6002-WG/WG+,

IAP-6002-WG/WG+ is a reliable 802.11b/g WLAN with 2 ports LAN Access Point. It can be configured to operate in AP/ Bridge/Repeater/AP-Client mode. You are able to configure IAP-6002-WG/WG+ by WEB interface via LAN port or WLAN interface. IAP-6002-WG/WG+ provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IAP-6002-WG+ also provides PD feature on ETH2 which is fully compliant with IEEE802.3af P.O.E. PD specifi cation. Therefore, IAP-6002-WG/WG+ are one of the best communication solutions for wireless applications on the industrial network.

Features

•	WLAN interface support up to 54Mbps link speed
•	Various kinds of operation modes supported: AP/Bridge/ Repeater/AP-Client mode
•	Various kinds of encryption supported: WEP/WPA/WPAPSK(TKIP,AES)/WPA2/ WPA2-PSK(TKIP,AES)/Radius
•	Dual redundant Ethernet port support redundant mode (Recovery time < 10ms)
•	Ethernet switch mode enable Daisy Chain
•	Wireless connecting status monitoring
•	Versatile modes & event alarm by e-mail
•	HTTPs protocol supported for secured management
•	IP table to prevent access from unauthorized IP address
•	IP Confi gurable by Windows utility (AP-Tool)
•	1KV isolation for PoE PD port of IAP-6002-WG+
•	Dual redundant DC power inputs of terminal block
•	Rigid IP-30 housing design
•	DIN-Rail and panel mounting enabled

	IAP-6002-WG	IAP-6002-WG+
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX	2
P.O.E. PD port		Present at ETH2 Fully compliant with IEEE 802.3af Power Device specifi cation Over load & short circuit protection Isolation Voltage: 1000 VDC min. Isolation Resistance : 108 ohms min

WLAN interface

Operating Mode	AP/Bridge/Repeater/AP-Client
Antenna and connector	2dBi antenna on reverse SMA connector
Radio Frequency Type	DSSS
Modulation	IEEE802.11b : CCK, DQPSK, DBPSK IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band	America/FCC : 2.412~2.462 GHz (11 channels) Europe CE/ETSI : 2.412~2.472 Ghz (13 channels)
Transmission Rate	IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps IEEE802.11g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power	IEEE802.11b/g : 18dBm
Receiver Sensitivity	-81dBm @ 11Mbps, PER< 8%; -64dBm @ 54Mbps, PER< 10%
Encryption Security	WEP : (64-bit ,128-bit key supported) WPA : WPA2 : 802.11i(WEP and AES encryption) PSK (256-bit key pre-shared key supported) Radius supported TKIP encryption
Wireless Security	SSID broadcast disable

LED Indicators

Power Indicator	PWR 1(2)(P.O.E.) / Ready : Red On : Power is on and booting up. Green On : Power is on and functioning Normally.
10/100TX RJ45 Port Indicator	Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps
WLAN LEDs	WLAN Link /ACT : Green WLAN Strength : 1<25%, 2<50%, 3<75%, 4<100%
Fault	Red : Ethernet link down or power down

Fault contact

Relay

Relay output to carry capacity of 1A at 24VDC

Power

Redundant Input Power	Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.)	6 Watts
Overload Current Protection	Present
Reverse Polarity Protection	Present on terminal block

Physical Characteristic

Enclosure	IP-30
Dimension (W x D x H)	52(W) x 106.1(D) x 144.3(H) mm (2.05x4.18x5.68 inch.)
Weight (g)	800 g	804 g

Environmental

Storage Temperature	-40 to 85°C (-40 to 185°F)
Operating Temperature	-10 to 55°C (14 to 131°F)
Operating Humidity	5% to 95% Non-condensing

Regulatory approvals

EMI	FCC Part 15, CISPR (EN55022) class A
EMS	EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock	IEC60068-2-27
Free Fall	IEC60068-2-32
Vibration	IEC60068-2-6
Safety	EN60950
Warranty	3 years

Available Model

Model No.	Description
IAP-6002-WG	Industrial 802.11 b/g Redundant Access Point
IAP-6002-WG+	Industrial 802.11 b/g Redundant Access Point with 1-port PoE PD