IDS-5042-I+ is an innovative 4 port isolated RS422/485 to 2 ports LAN redundant device server. To assure the agility and security of critical data, IDS-5042-I+ offers many powerful features for HW & SW redundant functions. When the connection between master-link and LAN fails, IDS-5042-I+ can automatically switch to another LAN port within 10mS, and still guarantees a non-stop connection. IDS-5042-I+ also supports switch mode, users can use Daisy Chain to reduce the usage of Ethernet switch ports. Secondly, IDS-5042-I+ can simultaneously transfer data into 5 host PCs. This feature can assure all critical data that saved in different host PC to avoid Ethernet break or host PCs failure. Thirdly, IDS-5042-I+ provides dual redundant power inputs on DC power jack and terminal block. IDS-5042-I+ also provides NAT pass through function so that users are able to manage IDS-5042-I+ inside or outside the NAT router. It is easy for different IP domain users to use IDS-5042-I+. In addition, IDS-5042+ also support PoE. PD on ETH2. This feature is fully compliant with IEEE802.3af standard. Therefore, IDS-5042-I+ is one of the best communication redundant solutions for application of serial devices.
Product Features
•
Dual redundant Ethernet port support redundant mode (Recovery time < 10ms)
•
Ethernet switch mode enable Daisy Chain
•
Redundant 5 multiple host devices supported to protect your industrial network
•
Versatile modes & event alarm by e-mail
•
HTTPs & SSH protocol supported for secured management
•
NAT router pass through
•
IP table to prevent access from unauthorized IP address
•
Confi gurable by Web-based and Windows utility (DS-Tool)
•
2KV isolation for RS422/485 serial port
•
1KV isolation for PoE PD port
•
Dual redundant DC power inputs of terminal block
•
Rigid IP-30 housing design
•
DIN-Rail and panel mounting enabled
Product Features
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX
2
PoE Feature
PoE.Present at ETH2
Power Device (IEEE 802.3af ) :
IEEE 802.3af compliant input interface
Power consumption : 8Watts max.
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : ohms min
Serial Ports
Connector
5 pin terminal block x 4
Operation Mode
RS422 / 4(2)-Wire RS485. Which can be confi gured by DS-Tool
Serial Baud Rate
110 bps to 460.8 Kbps
Data Bits
5, 6, 7, 8
Parity
odd, even, none, mark, space
Stop Bits
1, 1.5, 2
RS-422
Tx+,Tx-, Rx+, Rx-,GND
RS-485 (4-wire)
Tx+,Tx-, Rx+, Rx-,GND
RS-485 (2-wire)
Data+, Data-,GND
Isolating
2KV
Flow Control
XON/XOFF, RTS/CTS, DTR/DSR
LED Indicators
Power Indicator
PWR 1(2) / Ready :
Red On : Power is on and booting up.
Red Blinking : Indicates an IP confl ict, or DHCP or BOOTP server did not respond properly.
Green On : Power is on and functioning Normally.
Green Blinking : Located by Administrator.
10/100TX RJ45 Port Indicator
Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps.
Serial TX / RX LEDs
Red : Serial port is receiving data
Green : Serial port is transmitting data
Power
Redundant Input power
Dual DC inputs. 12-48VDC on 6-pin terminal block and power jack
Power Consumption (Typ.)
5.5 Watts
Overload Current Protection
Present
Reverse polarity protection
Present on terminal block
Physical Characteristic
Enclosure
IP-30
Dimension (W x D x H)
52(W) x 106.1(D) x 144.3(H) mm (2.05x4.18x5.68 inch.)
Introduction 
ohms min
